Saskatoon Neighbourhood HVAC Guide: What to Expect in Every Part of the City
Saskatoon is a younger city than most, so the heating equipment in a house usually says as much about the decade it was built as the street it is on. Here is what is typical, era by era and area by area.
Most Saskatoon homes were built after 1960. Walk through the older neighbourhoods near the river and you will find houses from the 1910s and 1920s that have been heated three different ways since they were built. Drive out to the newest edge of the city and the house may be less than ten years old, with a condensing furnace, a ventilation unit and a thermostat that talks to a phone. The equipment in each reflects what was standard when the house went up, and what the owners since then chose to replace.
That matters if you are buying, inheriting, renting out or simply trying to understand what is in your basement. A better-informed owner has a better conversation with a heating contractor: you can describe the age of the furnace, say whether there is a ventilation unit, and ask sensible questions about the options. This guide is meant to help with that. It does not replace an inspection, and it cannot tell you what is in any one house. The profiles describe what is common in each area, and individual streets and blocks differ.
The guide starts with how Saskatoon's housing stock and climate actually compare with what people assume, then covers the heating and cooling setups you will meet, then walks through the city by era and area: the older core, the post-war neighbourhoods, the 1960s to 1980s suburbs, and the newer growth areas.
Saskatoon Housing Stock at a Glance
The City of Saskatoon publishes a neighbourhood profile for each of its 63 neighbourhoods, built on the 2021 Census and the City's own dwelling counts. The profiles report the age of dwellings, the mix of housing types and whether homes are owned or rented. They do not say what heats a home, so the age of the housing is the best published clue to what you are likely to find. Across the city, the profiles count 128,658 dwellings.
| Period of construction | Share of dwellings |
|---|---|
| 1960 or before | 16% |
| 1961 to 1980 | 30% |
| 1981 to 1990 | 15% |
| 1991 to 2000 | 8% |
| 2001 to 2005 | 5% |
| 2006 to 2010 | 7% |
| 2011 to 2016 | 11% |
| 2016 to 2021 | 8% |
Source: City of Saskatoon, Neighbourhood Profiles, 24th edition (December 2025). Age of dwelling is the census period in which the building was originally built, as reported by respondents to the best of their knowledge. Percentages are rounded.
Two things stand out. Only about one dwelling in six was built in 1960 or before, which is a much smaller share than in many older Canadian cities. And roughly one in four (26%) was built since 2006. Saskatoon's typical house is not a century home. It is a 1960s to 1980s house on its first or second furnace, or a house from the last twenty years. Overall, 47% of dwellings are single-family, 13% are two-unit and 40% are in multi-unit buildings (apartments, condos and townhouse blocks), and about 65% of homes are owner-occupied.
The mix changes a lot from one neighbourhood to the next. The table compares four areas chosen to span the city's range: an older core neighbourhood, a mid-century neighbourhood, a 1980s and 1990s suburb and one of the newest growth areas.
| Area | 1960 or before | 1961 to 1980 | 1981 to 2000 | 2001 to 2021 | Owner-occupied |
|---|---|---|---|---|---|
| City of Saskatoon | 16% | 30% | 23% | 31% | 65% |
| Caswell Hill | 71% | 15% | 7% | 8% | 60% |
| Mount Royal | 44% | 44% | 7% | 4% | 61% |
| Erindale | 0% | 3% | 91% | 5% | 91% |
| Stonebridge | 0% | 1% | 2% | 96% | 66% |
Source: City of Saskatoon, Neighbourhood Profiles, 24th edition. The 1981 to 2000 and 2001 to 2021 columns add the City's separate periods together, so rows may differ from 100% by a point or two. In fast-growing areas such as Stonebridge, thousands of homes were finished after the 2021 Census, so the era figures describe the homes that existed in 2021, not the whole neighbourhood today.
The pattern is clear. Caswell Hill is the oldest housing in the table: seven in ten homes date from 1960 or before. Mount Royal splits almost evenly between pre-1960 and 1961 to 1980. Erindale is a 1980s and 1990s neighbourhood almost entirely. In Stonebridge nearly everything counted was built after 2005. Whether a particular house has an old furnace, a newer one or a heat pump can only be confirmed by looking at it, but the era narrows the questions considerably.
Saskatoon's Climate: Colder and Drier Than You Might Think, Not Hotter
Environment and Climate Change Canada's 1991 to 2020 climate normals give a useful picture of what the equipment has to do. At the Saskatoon airport station, the average January day is -15.4 °C, the average July day is 18.3 °C, and the year averages 2.4 °C. Heating degree-days (a measure of how much heating a climate demands, counted below 18 °C) come to about 5,791 a year. Cooling degree-days above 18 °C are only about 105.
Saskatoon also records fierce short cold snaps: the lowest daily minimum in the 1991 to 2020 period was -44.9 °C, in January 2004.
What that means for a homeowner: the furnace is the system that does most of the work. Many Saskatoon homes can be comfortable in summer with window units, a ceiling fan or a modest cooling setup, and central air is often a comfort choice rather than a necessity. Heating is not optional, and an unreliable furnace in the cold months is the failure most worth preventing.
Who Supplies What: Gas and Electricity in Saskatoon
Natural gas in Saskatoon comes from SaskEnergy, a Crown corporation. Electricity in Saskatoon has a feature that many cities do not: it is split between two utilities. Saskatoon Light & Power, the City's own utility, serves customers within the 1958 city boundary (with the University of Saskatchewan excepted). SaskPower serves the areas annexed since. The City lists several neighbourhoods as served by both, including Arbor Creek, College Park East, Erindale, Evergreen and Westview, plus industrial areas.
For a gas furnace, the electricity supplier makes no difference. It matters if you are looking at electric heat or a heat pump, because the utility serving your address may affect which programs and rates apply. If you are not sure who serves your street, your electricity bill will tell you.
Understanding the Heating and Cooling Setups
Most Saskatoon houses fall into one of a handful of configurations. The mix leans heavily towards gas forced air, with other setups concentrated in older and multi-unit buildings.
Gas forced-air furnace, with or without central AC
This is the standard setup in the large majority of Saskatoon houses built from the 1960s onward, and in many older houses that have been updated since. A gas furnace, supplied by SaskEnergy, heats air and pushes it through ducts to registers. If central air is present it uses the same ducts and blower, with a refrigerant coil and an outdoor condensing unit. If the ducts are already in place, adding central air is usually a simpler job than in a house without them, though sizing and the electrical panel still need to be checked.
The furnace you find will tell you roughly when it was installed. Older mid-efficiency furnaces vent through a metal flue or the chimney. High-efficiency (condensing) furnaces vent through plastic (PVC or similar) pipe out a side wall and drain condensate to a floor drain or pump. Since 2019, federal regulations have required most newly manufactured residential gas furnaces to be high-efficiency (95% AFUE), so a replacement installed in recent years is very likely condensing.
- Ask for the installation year of the furnace and the date of the last service.
- Look at the venting: a metal flue to the chimney suggests an older, mid-efficiency unit; plastic pipe through the wall suggests a condensing unit.
- Confirm whether central AC exists. The outdoor condensing unit is the visual tell.
- Check the filter location and the condition of the filter.
- Ask who did the work and whether a gas permit was taken out for the installation (see "Permits and Licensing" below).
Hot-water boiler and radiators (or baseboard)
Some older houses and many older multi-unit buildings are heated by a boiler that circulates hot water to radiators or baseboard heaters. There is no forced air, and so no central AC without a separate system. With only 16% of the city's dwellings built in 1960 or before, boiler houses are likely to be a smaller part of the market than in some older cities. If you are looking at an older house or a walk-up apartment building, it is worth asking.
- Ask the age of the boiler and when it was last serviced by a licensed gas contractor.
- Walk the house and confirm every radiator or baseboard unit is present and warms up.
- If the home is a condo or apartment, ask whether the boiler is in-suite or building-wide and who is responsible for it.
Heat pumps and ductless mini-splits
A ductless mini-split pairs a wall-mounted indoor unit with an outdoor compressor. It can cool, and cold-climate models are designed to heat too. In Saskatoon, mini-splits are most useful in houses without ducts, in additions and in basement suites. Where a heat pump is added to a house with a gas furnace, the furnace can stay as backup for the coldest weeks, a setup sometimes called a hybrid or dual-fuel system. SaskEnergy mentions hybrid heat-pump systems in its heating guidance. How much a heat pump saves depends on how cold the weather is, what you pay for gas versus electricity, and how the system is set up, so it is worth asking a contractor to walk through that for your house rather than relying on a general rule.
- Count the indoor units and ask what each one covers.
- Ask whether the outdoor unit is rated for Saskatoon winters, and what the backup heat is when it is very cold.
- Ask which utility serves the address, since that can affect electricity-related programs.
Electric baseboards, window units and no central cooling
Some basements, additions, garage suites and small older homes rely partly or wholly on electric baseboard heat. Window air conditioners are common wherever there are no ducts. In a city with about 105 cooling degree-days a year, plenty of households choose to manage with a window unit or two. If you are buying, ask what rooms are heated by what, and how the electricity bill looks in January.
If you smell natural gas, leave the building immediately. SaskEnergy says not to use electrical switches, appliances, telephones or vehicles near the smell, and to call its 24-hour emergency line at 1-888-700-0427 from a safe place. If a carbon monoxide alarm sounds, leave the building and call 911 or SaskEnergy's emergency line, and stay out until responders say it is safe. Carbon monoxide alarms are required in Saskatchewan residential buildings, including older ones. Gas heating equipment should be installed by a licensed gas contractor and inspected every year. Do not attempt gas work yourself.
Permits and Licensing in Saskatoon
In Saskatchewan, gas installations are regulated by the Technical Safety Authority of Saskatchewan (TSASK). TSASK says only licensed gas contractors are permitted to do gas installations and to request a gas permit, and that a permit is required before the work starts. A gas inspector may choose to inspect the work, which can include the furnace, chimney, piping and appliances. TSASK has a Find a Licensed Contractor tool on its website. SaskEnergy's rebates also require that the equipment be installed by a TSASK-licensed gas contractor, and self-installation is excluded.
Building permits and energy requirements are handled by the City of Saskatoon. For residential permit applications received on or after September 15, 2025, the City applies a Tier 2 minimum energy requirement under the 2020 National Building Code, which Saskatchewan adopted effective January 1, 2024. What that means for a specific furnace or addition is a question for the City and your contractor, so check before relying on any summary, including this one.
When buying, it is reasonable to ask the seller whether past gas work, such as a furnace or water heater replacement, was done by a licensed gas contractor with a permit. It can make the paperwork around a sale simpler.
Neighbourhood Profiles by Era and Area
The profiles below describe the dominant housing in each area and what is typical for homes of that era. An infill house on a 1910s lot, or a renovation that replaced the original system, will differ from the neighbourhood norm. Use these as a starting point for questions.
The Older Core: Caswell Hill, Nutana, Riversdale and Neighbours
Caswell Hill is the clearest older-house example in the city. Seven in ten homes date from 1960 or before and about two-thirds of dwellings are single-family, with some suites and apartments and a share of newer infill. Development began around 1905, with character homes, small wartime houses and later infill. Natural gas reached Saskatoon in the early 1950s, so houses from the 1910s to 1940s were originally heated with coal or wood and converted later. In that kind of house it is common to find an upgraded system layered over the original structure: ducts added to rooms that were never designed for them, wiring and panels that have been upgraded at different times, and in some larger houses a hot-water system. Cooling is mostly window units or a mini-split.
- Ask what the house was originally heated by and when it was converted.
- Look at how the ducts run. Retrofitted ductwork can leave some rooms over- or under-heated, and older ducts may be poorly insulated or leaky.
- Ask about the electrical panel and the age of the wiring if you plan to add a mini-split, since it usually needs its own circuit.
- If there is a basement suite, ask how it is heated and ventilated and whether it was permitted.
Nutana is Saskatoon's original settlement area, on the east side of the river. About 44% of dwellings are from 1960 or before, but 61% of dwellings are in multi-unit buildings and about half of homes are rented, so the neighbourhood is a mix of older houses and apartment and condo buildings. For a house, the questions are similar to Caswell Hill. For a condo or apartment, the first question is what the building provides: central boiler, in-suite furnace, electric baseboard, and who maintains the equipment.
Riversdale shows the redevelopment pattern: 52% of dwellings date from 1960 or before and about a quarter are from 2001 or later, with a redevelopment boom from about 2012. Just over half of homes are rented. On a single block, a pre-1960 house can sit next to new infill with modern high-efficiency equipment and ventilation, so check each property on its own. For rental properties, ask who is responsible for furnace servicing and the filter, and how often it has happened.
Haultain, Mayfair, Westmount, King George and Queen Elizabeth are other older neighbourhoods in the City profiles, where roughly half or more of dwellings are from 1960 or before and two-unit housing is common (about 31% of dwellings in Haultain and Mayfair, for example). Expect much the same story as Caswell Hill: older houses with updated systems and some suites. Suites are worth a specific question, because a furnace sized for one household now serves two.
Buena Vista (62% from 1960 or before), Kelsey-Woodlawn (59%), Avalon (55%) and Adelaide/Churchill (54%) belong in the same group, as do Holiday Park, North Park, Exhibition and Grosvenor Park, where about four in ten dwellings are that old. In Avalon and Adelaide/Churchill, the rest is mostly 1960s and 1970s housing, so the furnace history matters more than the street's reputation.
City Park is often thought of as an older neighbourhood, but the City profile shows 79% of its dwellings in multi-unit buildings and 72% rented, with about a third built in 1960 or before. The same is true of downtown and the City's "urban centre" areas. If you are buying a condo, the building's heating and cooling are mostly a building-level question: ask the condo corporation for the age and service history of the boiler, fan coils or in-suite equipment, and what your unit is responsible for.
Post-War Neighbourhoods: Varsity View, Montgomery Place and Mount Royal
Varsity View grew with the University of Saskatchewan, which was founded in 1907, and was annexed in 1911. Many of its homes date from 1946 to 1960, but the City profile shows a mixed picture: 37% from 1960 or before, about 29% from 1961 to 1980 and about 20% from 2001 or later. Only 43% of homes are owner-occupied, and a third of dwellings are in multi-unit buildings. That tends to mean post-war bungalows and older houses, many of them rented, with newer infill alongside. If you rent, ask your landlord when the furnace was last serviced. If you are buying a rental-heavy house, ask for service records, because furnaces in rental properties sometimes get less attention than in owner-occupied homes.
Montgomery Place has a history that no other Saskatoon neighbourhood shares. It was built after the Second World War for returning veterans under the Veterans' Land Act, was annexed in the 1950s, has large lots and was designated a National Historic Site in 2016. The City profile shows 19% of dwellings from 1960 or before, 39% from 1961 to 1980, and a notable share (around a fifth) from 2011 or later, which reflects infill on those large lots. Owner-occupancy is 77%. Expect houses that have been renovated and re-heated several times, from original postwar construction to new builds on subdivided or replaced properties, so the equipment can vary a lot from one lot to the next.
Mount Royal is the neighbourhood closest to the "typical" Saskatoon mid-century profile: 44% from 1960 or before, 44% from 1961 to 1980, and only a small share built since. About 61% of homes are owner-occupied. Most houses here are on their second or third furnace. Many will have had a furnace replacement in the last 15 to 20 years, but not all, and some may still have a furnace that is decades old. The questions for a buyer are the age and efficiency of the furnace, whether the water heater and furnace share a chimney flue, and the condition of the ducts.
- Ask for the furnace age and last service date. A furnace that is 25 years or older is worth a conversation with a contractor about what to expect.
- If there is a chimney flue shared by a furnace and a water heater, ask whether the venting was reviewed when either one was replaced.
- Ask whether the home has central AC. Many mid-century houses do not.
- Confirm there is a working carbon monoxide alarm on each floor.
The 1961 to 1980 Bungalow Belt
Several Saskatoon neighbourhoods were built almost entirely between 1961 and 1980. In the City profiles, Eastview (85%), Pacific Heights (85%), River Heights (83%), Brevoort Park (79%), Massey Place (79%), College Park East (79%), College Park (77%) and Nutana Park (72%) all have most of their dwellings in that band. These are the neighbourhoods where the original furnace has most likely been replaced at least once, and often twice. The age of the furnace now in the basement is the key question. A furnace installed in the 2000s may be mid-efficiency and nearing the end of its range. A newer one is probably condensing. What distinguishes these neighbourhoods from each other is mostly tenure and lot size, for example Pacific Heights is about 80% owner-occupied and Eastview about 68%.
Richmond Heights (87%), Confederation Park (64%), Greystone Heights (62%), Fairhaven (60%) and Westview (54%) follow the same pattern. Fairhaven has about half of its dwellings in multi-unit buildings, so for a condo or townhouse, start with what the building or corporation looks after.
- Ask how many furnaces the house has had, and when the current one went in.
- Check the ducts and registers: houses from this era often have ducts routed through the basement ceiling, and some rooms may be harder to heat evenly.
- Ask about basement insulation and whether any rooms feel cold in winter.
The 1960s to 1980s Suburbs: Lawson Heights and Neighbours
Lawson Heights, in the north end, was a large suburban development. The City profile puts about 62% of its dwellings in the 1961 to 1980 band and 24% in 1981 to 1990, with a large share of multi-unit housing (about 43%) and about 62% of homes owner-occupied. Building ran into the 1980s, so treat the era as roughly the 1960s through the 1980s and check the individual house. Houses from this stretch are the group most likely to have a first-generation or second-generation furnace, and 1980s houses that were built tighter than their predecessors may have some form of mechanical ventilation, which is worth asking about.
Elsewhere in the city, Silverwood Heights (72% built 1981 to 1990), Lakeview (61% built 1981 to 1990), Lakeridge and Dundonald are 1980s suburbs. A 1980s furnace that has not been replaced is now well past 30 years old. More likely it has been replaced once, sometimes with another mid-efficiency unit, sometimes with a high-efficiency one.
Other neighbourhoods span several decades, so the individual house matters more than the area. Holliston and Hudson Bay Park are mostly split between 1960 or before and 1961 to 1980. Forest Grove and Parkridge are mostly split between 1961 to 1980 and 1981 to 1990. Sutherland and Wildwood have about four in ten dwellings from 1961 to 1980 and the rest spread across later decades. Pleasant Hill has a similar spread, starting earlier, and about 60% of its dwellings are in multi-unit buildings.
1980s and 1990s Family Suburbs: Erindale, Dundonald and Briarwood
Erindale is the clearest example of this era: 52% of dwellings built from 1981 to 1990 and 39% from 1991 to 2000, with 77% single-family and about 91% owner-occupied. Most homes date from 1986 to 2001. It is also one of the neighbourhoods where electricity comes from both Saskatoon Light & Power and SaskPower. A house from the 1990s may have been built with mid-efficiency equipment and, in the later part of that decade, with some mechanical ventilation. By now the original furnace and air conditioner are often at or past the point where owners start budgeting for replacement. This is the cohort where a "repair or replace" conversation comes up most often (see our guide to furnace repair versus replacement in Saskatoon).
Briarwood and its neighbours Silverspring and Arbor Creek are newer. In Briarwood, 28% of dwellings were built from 1991 to 2000 and 43% from 2001 to 2005, with a further 19% from 2006 to 2010, about 74% single-family and about 95% owner-occupied. Homes from this period are typically a first-generation high-efficiency or late mid-efficiency furnace, often with central AC and a ventilation unit. They are now 15 to 30 years old. Components such as the AC condenser, the humidifier and the ventilation unit's filters are the usual maintenance items.
- Ask whether the home has a heat recovery ventilator (HRV) or similar ventilation unit, where it is, and when its filter was last cleaned.
- Ask the age of the AC condensing unit and whether it has been serviced.
- Check the condensate drain and the PVC venting on high-efficiency furnaces for obvious damage or blockage.
- Ask whether a humidifier is installed and if it is maintained.
The Newer Growth Areas: Stonebridge, Rosewood, Brighton, Evergreen and Beyond
Stonebridge is the City's largest neighbourhood by dwelling count (6,311 in the 2024 count), with the great majority of the homes counted in the 2021 Census built from 2006 on, and about half of dwellings in multi-unit buildings. Rosewood, where servicing started in 2008 and first homes appeared in 2009, has 4,293 dwellings, nearly all built from 2011 on, with 26% two-unit housing. Brighton, Evergreen, Kensington, Aspen Ridge and Willowgrove are other recent areas, where census-era figures understate the neighbourhoods because so much was built afterwards. Treat all the era figures for these areas as describing only the early homes.
Hampton Village (about 90% built from 2006 to 2016) and The Willows (mostly from 2006 to 2016) sit in the same group.
Homes in these areas are typically built to modern energy codes, with condensing gas furnaces, a ventilation system (commonly an HRV or similar) and often central air. Because the code has changed over time, a 2008 house and a 2024 house in the same neighbourhood can have noticeably different envelopes and equipment. Many of these homes are still within their warranty periods, or have only recently left them. The common issues are less about wear and more about maintenance that new owners do not know they need: HRV filters, furnace filters, condensate drains and the AC. Heat pumps and hybrid systems are part of the conversation for new buyers, especially in homes built since the more recent energy requirements.
- Ask for the manuals and the warranty information for the furnace, AC and ventilation unit. If the original builder installed them, find out what the warranty covers and for how long.
- Ask whether the ventilation unit was balanced when installed. Current Saskatchewan code material for ventilation design refers to balancing HRVs and posting the results on the unit.
- For a home with a basement or garage suite, ask how each space is heated and ventilated.
- Check the AC condensing unit for damage and the condensate drain for clogs.
The HVAC Maintenance Many Saskatoon Homeowners Skip
Most owners call a contractor only when something stops. The failures most likely to leave you cold on a January morning are the ones a yearly visit tends to catch.
Furnace tune-up
TSASK recommends that a licensed contractor inspect fuel-burning appliances once a year. A tune-up typically covers the burners, the heat exchanger, the blower and fan, the controls and the venting. It is also when you can ask the contractor about the age and condition of the unit.
Filters
SaskEnergy suggests cleaning or replacing the furnace filter every one to two months during the heating season. It is one of the simplest jobs, and often the one that gets forgotten.
Ventilation unit (HRV) service
If your home has an HRV, it has filters and a core that need regular attention, and the intake and exhaust hoods outside should be kept clear of snow and ice. If you are not sure whether you have one, look for a box in the basement or utility room with two ducts to outside and several to the house, and ask the contractor to point it out.
Air conditioning
In a city with a short cooling season, the AC is easy to ignore. A check before the first hot week is a good time to clean the outdoor coil, look at the drain and check the electrical connections.
Carbon monoxide alarms
SaskEnergy suggests one alarm on every floor, near bedrooms and near the door from an attached garage, tested monthly. Alarms expire, typically after five to seven years, so check the date on the label.
Costs vary by contractor and by the size and age of the system. For current Saskatoon ranges for diagnostics, repairs and replacement, see our Saskatoon furnace repair cost guide.
Rebates and financing for Saskatoon homeowners
Last checked: November 6, 2026
Program terms change, sometimes several times a year. This table shows what each program's official page said on the date above. Check the link for current terms before you sign a contract, because most programs set conditions on who installs the equipment and when you apply.
| Program | Status | Amount | Key conditions |
|---|---|---|---|
| Residential Equipment Replacement Rebate SaskEnergy |
Open. Terms effective August 17, 2026; funding limited | Furnace $325 · boiler $750 · combi boiler $800 · tankless water heater $1,000 · condensing water heater $1,000 | Furnace 97.0%+ AFUE; boiler and combi 95.0%+ AFUE; tankless 0.87+ UEF; condensing tank 0.80+ UEF. Existing homes only (not new construction). Installed by a gas contractor licensed through the Technical Safety Authority of Saskatchewan; self-installs not eligible. Apply within 120 days of installation. |
| Home Energy Loan Program (HELP) City of Saskatoon |
Open. Accepting applications | Loan of $1,000 to $40,000 (up to $60,000 if the project cuts energy use 50% or more); 2026 rates 3.24% (5 yr), 4.03% (10 yr), 4.83% (20 yr); $750 admin fee | Owner-occupied single-family, semi-detached, row or non-apartment condo inside city limits. EnerGuide evaluation before and after; work can't start before the agreement is signed. Repaid through property taxes. Eligible upgrades include ENERGY STAR furnaces and boilers, gas tankless and storage water heaters, cold-climate heat pumps. |
| Heat pump rebate (One Million Home Energy Retrofits) Government of Canada |
Announced. Applications open early 2027; heat pumps installed from November 1, 2026 can be claimed | $2,000; up to $10,000 for households at or below the median income | Homeowner, one rebate per household. Cold-climate heat pump on the eligible product list, bought from and installed by an HVAC contractor. Receipts within 6 months. No payments until the program launches. |
| Canada Greener Homes Grant Natural Resources Canada |
Closed. Last day to submit documents was December 31, 2025 | — | No new applications or claims. |
| Canada Greener Homes Loan Natural Resources Canada |
Closed to new applications | — | No further applications can be approved; loans already approved are unaffected. |
| Oil to Heat Pump Affordability Natural Resources Canada |
Closed to new applications July 31, 2026; existing applications still processed | — | Was for homes switching from oil heat to a heat pump, so it rarely applied to Saskatoon's gas-heated homes. |
Closed programs are listed because many homeowners still ask about them. Amounts are per unit, before tax, and paid by the program, not the contractor, unless the program says otherwise.
Talking to a Contractor: Questions Worth Asking
Whatever era your house is from, a few questions tend to lead to a useful conversation. None of them is a test. They help a contractor give you advice that fits your house.
- "How old is my furnace, and what does its condition tell you about what to expect over the next few years?"
- "Is it worth repairing, or should I be planning for replacement? What would you look at to decide?" (See furnace repair versus replacement in Saskatoon.)
- "If I replace it, what are my options, and will the venting, drain and electrical work change?"
- "Will the work be done under a gas permit, and who arranges it?"
- "Does my house have ventilation, and does it need servicing?"
- "Is anything here a safety concern, such as venting, a cracked heat exchanger or carbon monoxide?"
If you are looking for licensed gas contractors serving Saskatoon, use TSASK's Find a Licensed Contractor tool to confirm a licence before you book.
Directory · 3 companies
Top-rated HVAC companies in Saskatoon
Independently selected on Google rating, review volume and years in Saskatoon. Every company here is rated 4.7 or higher. Tap one to open its Google listing, with phone number, hours and recent reviews.
-
View on Google
Centennial Plumbing, Heating & Electrical
Saskatoon family business since 1967. Heating, cooling, boilers, water heaters, plumbing and electrical.
-
View on Google
Razor Heating & A/C
Owner-led Saskatoon company since 2007. Furnaces, air conditioning, heat pumps, boilers and water heaters.
-
View on Google
Efficiency Heating & Cooling
Locally owned Saskatoon company since 1985. Furnaces, air conditioning, heat pumps, water heaters and tankless systems.
Frequently Asked Questions
No. According to the City of Saskatoon's neighbourhood profiles, about 16% of Saskatoon dwellings were built in 1960 or before, and 30% from 1961 to 1980. About 26% were built since 2006. The typical Saskatoon house is a 1960s to 1980s home or a house from the last twenty years, and only a minority are pre-war.
Saskatoon averages about 5,791 heating degree-days a year (1991 to 2020 normals), and the coldest daily minimum in that period was -44.9 °C. Furnace sizing depends on your house, its insulation and the design temperature your contractor uses.
It is a comfort decision more than a necessity. Saskatoon averages about 105 cooling degree-days a year, so hot spells are short. Some households are comfortable with window units or a mini-split in the rooms they use most. If the house already has ducts, adding central air is usually simpler; if it has none, a ductless system is the usual route.
A licensed gas contractor. TSASK says only gas contractors are permitted to do gas installations and to request a gas permit. SaskEnergy's rebates also require installation by a TSASK-licensed gas contractor and do not cover self-installation. You can check a contractor's licence using the Find a Licensed Contractor tool on the TSASK website.
For a gas furnace, it does not. If you are considering electric heat or a heat pump, it can affect rates and programs. Saskatoon Light & Power serves addresses inside the 1958 city boundary and SaskPower serves the areas annexed since, with a few neighbourhoods, including Erindale, Arbor Creek, College Park East, Evergreen and Westview, served by both. Your electricity bill shows who supplies your address.
Start with the furnace: its age, its venting and its service history. Then ask whether there is central air, whether there is a ventilation unit (more likely in newer homes) and whether any basement or garage suite has its own heating. Ask whether past gas work was done by a licensed contractor, and confirm that carbon monoxide alarms are in place. A home inspector can look at the visible condition, and a licensed gas contractor can assess the heating equipment in more detail.
Sources and Method
Tables and the era and tenure figures in the profiles come from the City of Saskatoon's Neighbourhood Profiles (24th edition, December 2025), which use the 2021 Census for age of dwelling and the City's own dwelling counts. The profiles do not report what heats a home, so the heating and cooling comments describe what is typical for each era and are not counts. An individual street or house can differ from its neighbourhood. Rebate amounts appear only in the dated rebates section above.
- City of Saskatoon, Neighbourhood Profiles, 24th edition (December 2025)
- Environment and Climate Change Canada, Canadian Climate Normals 1991-2020 (Saskatoon Diefenbaker Int'l A)
- City of Saskatoon, Saskatoon Light & Power: About Us
- City of Saskatoon, Energy requirements for building permits
- Technical Safety Authority of Saskatchewan, Gas permit and inspection information
- SaskEnergy, Carbon Monoxide and Detecting a Leak
- SaskEnergy, Ways to Save: Heating
- SaskEnergy, Residential Equipment Replacement Rebate Program (installer licensing requirement)
- Canada Gazette, Regulations Amending the Energy Efficiency Regulations, 2016 (Amendment 15), SOR/2019-164
- Government of Saskatchewan, Saskatchewan adopts 2020 national construction codes
Last reviewed October 31, 2026. If you spot an error or have a newer source, corrections are welcome through the site contact page.