Furnace Not Working in Edmonton: Who to Call and What to Try
Rule out the one situation that is not a repair job, work through the quick checks in order, and match the fault to your furnace's age.
A furnace that has stopped usually points to the thermostat, power switch or breaker if nothing runs, an igniter, gas supply or pressure switch if it clicks without a flame, or a flame sensor or blocked venting if it lights and then stops. Edmonton sees about 389 hours a year that cold, so a furnace that stops in winter is a real problem. The first decision is who to phone. The second is what you can safely try while you wait.
First: Gas Emergency or Furnace Problem?
Smell gas? Do not try anything else on this page. ATCO Gas says to leave the area immediately, go to a neighbour's house and call ATCO Gas at 1-800-511-3447, 911 or your local fire department right away, day or night. Indoors, do not use matches or lighters, do not smoke, do not use your phone, and do not turn light switches or other electrical switches or appliances on or off. If a carbon monoxide alarm sounds, get everyone outside and call 911.
If there is no gas smell and no alarm, you have an equipment fault and a heating company is the right call.
| What you notice | Who to call |
|---|---|
| Gas smell near the furnace, stove or meter | Leave, then ATCO Gas at 1-800-511-3447 or 911 |
| Carbon monoxide alarm sounding | Get outside, then 911 |
| Furnace silent, or running with cold air, no smell | A licensed gas contractor, after the checks below |
Ten Minutes of Checks, in Order
These need no tools. Stop as soon as the heat comes back.
- The thermostat. Set to Heat and a few degrees above the room temperature. Replace the batteries, or restart a smart thermostat that has lost Wi-Fi.
- The power. Find the switch near the furnace and make sure it is on. At the panel, turn the furnace breaker off and on once. If it trips again, stop.
- The filter. Hold it to the light. If you cannot see through it, replace it, then give the furnace time to cool down before expecting a restart.
- The vent pipes. On a newer furnace, find the two plastic pipes on an outside wall. Frost, snow or debris around them can shut the furnace down. Clear around the openings by hand, and leave the pipes alone.
- One reset. If there is a reset button, press it once and watch a full cycle. If it fails again, resetting will not fix it.
Before you call, note any flashing code. It is usually decoded on a label inside the blower door, and it helps the technician bring the right part.
What Your Furnace's Age Says About the Fault
Edmonton is newer than most Prairie cities: about 38% of households in the metro area live in homes built before 1981, and about 40% in homes built since 2001. So the furnace in the basement could be almost anything.
Furnaces from the 1990s and 2000s
Many of these are now close to 20 years old. They are condensing furnaces, with plastic pipes and a condensate drain, and they shut down quickly on a safety. Common causes are a frosted or blocked pipe, a frozen condensate line (water in the pan below is a hint), a dirty flame sensor or a pressure switch fault. A furnace that lights and goes out after a few seconds points to the sensor or the venting.
Older mid-efficiency furnaces
If a metal flue runs from the furnace to a chimney, it is an older unit and may be on a second replacement. Typical no-heat faults are a failed igniter or pilot assembly, a tired blower motor or a poorly drafting flue. A pilot that will not stay lit is a fault. Follow only the lighting label on the furnace, try once or twice and then call.
Newer furnaces
A furnace under ten years old that stops is most often a blocked pipe, a filter or a thermostat problem, since the parts are still young.
If this is the third no-heat call in two winters, compare repair quotes with a new unit. Signs your furnace needs replacing and how long furnaces last in Alberta help.
Symptoms and Likely Causes
- Nothing, no fan, no click: thermostat, power switch or breaker.
- Fan blows cold air: the burner did not light, or the furnace locked out on overheating.
- Clicking but no flame: igniter, gas supply or pressure switch. Do not keep retrying.
- Lights, then stops: flame sensor or blocked venting.
- Starts and stops repeatedly: filter, venting or thermostat.
- Banging, grinding or squealing: blower or motor bearings. Switch it off and call.
Calling a Company
Gas furnace repair is restricted work for an Alberta Class B gasfitter, and contractors should be licensed with the City of Edmonton. Ask when you book. If it is the middle of the night, emergency furnace repair in Edmonton helps you decide whether to call now.
Tell them what the furnace did before it stopped, what you checked, its brand and rough age, any code, and whether the gas stove or water heater still works.
What a no-heat visit usually costs
A service call runs $100 to $150 in business hours. A flame sensor is $100 to $280, a hot surface igniter $150 to $300 and a pressure switch $200 to $310. Most furnace repairs overall land between $400 and $2,500. All figures are before GST. See furnace repair cost in Edmonton.
Staying Warm Until It Is Fixed
Close doors to rooms you do not need and gather in one room. Plug space heaters straight into a wall outlet, away from bedding and curtains, and do not leave them running unattended. Never heat with a gas oven, barbecue or generator indoors. If anyone at home is a baby, an older adult or unwell and the house keeps cooling, go somewhere warm for the night.
Directory · 5 companies
Top-rated furnace companies in Edmonton
Independently selected on Google rating, review volume and years in Edmonton. Every company here is rated 4.7 or higher. Tap one to open its Google listing, with phone number, hours and recent reviews.
-
View on Google
Friesen's Climate Control
Family owned and operated in Edmonton since 2007. Furnaces, air conditioning, heat pumps, water heaters and HRVs.
-
View on Google
Otto Heating & Cooling
Serving Edmonton since 2007. Furnaces, air conditioning, heat pumps and water heaters.
-
View on Google
Trust Home Comfort
Edmonton heating and cooling company on 27 Avenue NW. Furnaces, air conditioning, heat pumps and water heaters.
-
View on Google
Weiss-Johnson Heating, AC & Plumbing
Edmonton family business since 1977. Furnaces, air conditioning, heat pumps, boilers, water heaters, plumbing and HRVs.
-
View on Google
Acclaimed! Heating, Cooling & Furnace Cleaning
Family-owned Edmonton company since 1995. Furnaces, furnace cleaning, air conditioning, heat pumps and water heaters.
Frequently Asked Questions
Either the burner is not lighting or the furnace shut down on a safety. Set the thermostat fan to Auto, change a clogged filter, clear the outside pipes and press reset once. If the air stays cold, call a company.
A dirty filter, blocked vent pipes and a coated flame sensor are the usual causes. A new filter and clear pipes fix some cases. If it keeps happening, book a visit.
Yes. Frost or drifted snow can block the pipes on a high-efficiency furnace, and a condensate line in a cold corner can freeze. Clearing the openings takes two minutes. If it stops again, call a licensed gas contractor.
ATCO Gas at 1-800-511-3447 or 911 for a gas smell. For a carbon monoxide alarm, get outside and call 911. A heating company for a furnace that will not start when there is no smell.
Treat it as one when it is that cold, when children or older adults are home, or when the house is steadily cooling. Otherwise a first-appointment-of-the-day visit usually costs less than a night call.